Aerial Services Inc.
Mike Tully has been the President & CEO of Aerial Services, Inc. (Cedar Falls, IA) since 2002. He is a certified photogrammetrist, and has a B.S. in Forestry from Northern Arizona University, a M.S. in Forestry Entomology from the University of Maine, and a Masters in Business Administration from the University of Northern Iowa. He is a certified GIS-Professional, techno-geek, and the head of "Getting Right Things Done Well" at Aerial Services. Mike is an innovator and thinker.
New practitioners of drone-based remote sensing and mneed to understand the fundamentals of remote sensing, mapping, photogrammetry. Typical deliverables like orthophotography, digital elevation models (DEM), contours, cross-sections, and 3D models depend on this understanding. Nescience of these fundamentals is certain to cause considerable pain, financial loss and compromises to public safety. This article introduces the fundamentals of positional accuracy to help new practitioners provide these services consistent with professional accuracy standards.
I have talked with several practitioners that did not know what "ground control" was or how to use it to establish positional accuracy. This lack of familiarity is not uncommon among novices. They may not know that positional accuracy requirements are needed, or that they are often assumed by the client. They may not know how to discuss positional accuracy with their clients, nor how to measure the positional accuracy of their deliverables.
Truth 1: Positional accuracy doesn't just happen.
Professionals know that an accurate ortho (or DEM or 3D model) can look identical to an inaccurate one. Both are "pretty" pictures with lots of great detail, but one has more intrinsic value for a greater number of uses than the other because it is more accurate.
Truth 2: Positional accuracy is a product of the entire drone "system" (aircraft, sensors, operation, and processing software) not any single component.
It matters very little what the drone vendor says about the positional accuracy of its products. A combination of factors (and seldom a single factor) affects the positional accuracy of an orthophoto, DEM, or other derivative of remotely sensed data. Poor operation of the best drone can vitiate the positional accuracy of a deliverable. If a drone manufacturer claims their camera is accurate to two pixels for any given ground sample distance (GSD), the resultant positional accuracy for the orthophoto is dependent on each of the following factors. [The list below is not a comprehensive list of error sources but includes the major contributors of error.]
- the cameras inherent potential accuracy
- the stability of the flight
- the quality of the GPS data
- the quality of the inertial system (if the drone even uses one),
- the quality of the DEM used to make the orthophoto, and
- the type and quality of processing of the raw imagery into an orthophoto (this factor alone has several important sources of error from a "raw" to "finished" product)
- the number and quality of ground control points
Each factor contributes some error to the ultimate positional accuracy of the final product. The sum of all errors determines the measurable positional accuracy.
Truth #3: Positional accuracy standards exist and are important.
Understanding accuracy and accuracy standards sets your operations apart from others'. The American Society of Photogrammetry and Remote Sensing (ASPRS) is the major "standards body" for this profession. Their Standards for Geospatial Data reflect the realities of new sensors and digital data. They are "scale- and technology-agnostic". That is, the standards apply to data produced at any scale using any kind of sensor today or tomorrow. They can be used to measure and report the positional accuracy of geospatial deliverables like orthophotography, DEMs, digital surface models, 3D models, contours, topographic mapping, etc.
Deliverables with good, consistent positional accuracy can be an important differentiator for your drone-based remote sensing business. Unfortunately, a main cost driver of geospatial deliverables is positional accuracy. More accurate data will generally be more expensive than less accurate data. Profitability is highest when the required accuracy is not "over-engineered" and drives up costs.
Truth #4: Best possible positional accuracy today has error of 1 to 1.5 pixels (RMSE)
What level of positional accuracy is achievable using today's drone systems? Assuming "best practices" with a drone using a metric camera (most drones do NOT have a metric camera), high quality ground control, and solid production procedures (all difficult to achieve consistently) the best possible accuracy for orthos would have a root mean square error (RMSE) = 1 to 1.5 Pixels (GSD). Are these levels of accuracy achievable flying a drone with a non-metric camera and without any ground control? Not a chance … not today!
Because increasing accuracy comes at a premium it is imperative that the practitioner understand what accuracy is achievable from their drone "system", what the client expects, and what is needed (this is often at odds with client expectations) to meet the deliverable’s intended use. Because quality remote sensing products and services are difficult to deliver and need considerable expertise that is not yet programmed into the "easy button" , many drone fliers are choosing to collect data and have established firms like Aerial Services produce positionally accurate, irrefragable geospatial deliverables.